YONGRUI
Home › Replacement Gym Cables › How to Measure a Gym Cable

How to Measure a Gym Cable for Replacement or OEM Orders

To order a replacement or custom gym cable, we need five details: the finished length, the coated outside diameter, the steel-core diameter (if known), both end fittings and the coating type. Clear photos of both ends next to a ruler let our engineers check anything that is missing, usually without needing the original cable.

What you need to measure

DetailHow to get itToolExample
Finished lengthOverall length from the outer end of one end fitting to the outer end of the other, with the cable laid straight and not under loadSteel tape measure1,850 mm
Coated outside diameter (OD)At two or three unworn points along the coated sectionDigital caliper5.6 mm
Steel-core diameterFrom the original specification or a stripped end, if available. If not, skip it; we confirm it during technical reviewDigital caliper4.0 mm
End fittings (both ends)Identify the type, then record thread size, shank or ball diameter and eyelet hole diameterCaliper, thread gaugeM10 threaded plug
Coating and colourPA11 nylon, TPU, PU or PVC if known; any printing on the cablePhotoBlack PA11
Machine model and quantityFrom the nameplate or manualNoneCable crossover, 20 pcs
Gym cable measurement diagram A cable with a ball-end fitting on the left and an eyelet fitting on the right. Dimension A is the finished length, measured from the outer end of one fitting to the outer end of the other. Dimension B is the coated outside diameter. A · Finished length (outer end to outer end) B · Coated outside diameter End fitting 1 End fitting 2
Simplified diagram: A is the finished length, measured from the outer end of one fitting to the outer end of the other, including both fittings. B is the coated outside diameter. Illustrative, not to scale.

Step-by-step: measuring a gym cable

  1. Remove the cable safely

    Unload the weight stack and follow the equipment manufacturer’s maintenance instructions before removing the cable. Lay it straight on a flat surface.

    Safety: never remove or loosen a cable while the weight stack is loaded or raised.
  2. Measure the finished length

    With the cable straight and not under tension, measure the overall length from the outer end of one end fitting to the outer end of the other, as shown in the diagram. Record the result in millimetres and measure twice.

  3. Measure the coated outside diameter

    Use a caliper at two or three points along the coated section. Avoid worn, flattened or damaged areas, because they read smaller than the true diameter. Record the OD in millimetres.

  4. Identify and measure both end fittings

    Fittings can differ at each end, so check both. If you know the YR code (for example YR-1602-A), just send it and you can skip most dimensions; the full list is on our fittings page. Otherwise match each fitting to a type below and record its key dimensions.

    Fitting typeSeriesRecord
    Shank ball jointYR-1602Head diameter (8.5, 10, 11.6 or 14 mm), shank dimensions, overall length and inner hole diameter; do not confuse the cable-entry hole with the head diameter
    Metal eyelet jointYR-1603, YR-1604, YR-1618Eye inner diameter, overall length, inner hole diameter
    Screw bolt / thread plugYR-1610 (M8, M10), YR-1611 (M12, M14, M16)Thread size, thread length, head or hex size
    Clevis strap forkYR-1617Fork opening width, pin hole diameter, overall length
    Ball stopper / cable stopper / lock sleeve connectorYR-1606, YR-1605Ball or body diameter, overall length, how it is fixed (screw or crimp)
    Aluminum sleeve, cylinder, T-shape jointYR-1630, YR-1616, YR-1613Outer diameter, inner hole, overall length

    Complete cable sets can combine any two of these ends (our Gym Cable Set types 1–28), so tell us the type or code for each end separately.

  5. Note the coating and colour

    Record the coating material if you know it (PA11 nylon, TPU, PU or PVC), the colour, and any text or markings printed on the cable. If you are unsure, say so and send a photo.

  6. Photograph both ends and send

    Place each end beside a ruler or tape measure so the scale is visible. Take one photo from the side and one from the front or top of each fitting, then send them with your measurements, machine model and quantity.

How we define finished length

The method illustrated in this guide is overall length: measure from the outermost end of fitting 1 to the outermost end of fitting 2, including both fittings. Depending on the fitting, this may be the outer tip of a ball, the end of a threaded stud, the outer edge of an eyelet or the end face of a sleeve. If your original drawing uses bearing-point length, send the drawing or a photo with both reference points marked so we can help check the corresponding overall length. Confirm the measurement reference and final dimensions on the order drawing before production.

If your drawing uses a different convention, such as hole centre to hole centre, tell us and we will convert it. Do not subtract the fittings yourself.

Photos that help us quote faster

Common measuring mistakes

Copy and send this template

Paste this into an email or WhatsApp message and fill in what you know. Leave blanks for anything you are unsure about.

Machine model: ____
Finished length (mm): ____
Coated OD (mm): ____
Steel-core diameter (mm, if known): ____
End fitting 1 (YR code or type / size): ____
End fitting 2 (YR code or type / size): ____
Coating / colour: ____
Quantity: ____
Photos of both ends attached: yes / no

OEM buyers can send a technical drawing instead, with end-to-end dimensions, tolerances, coating, fittings and required quantity.

Frequently asked questions

Do I need to send the original cable?

No. For standard colours, clear photos and accurate measurements, or a technical drawing, are normally sufficient. A physical sample is only needed when an exact custom coating colour must be matched.

What if I cannot remove the cable from the machine?

Send photos of both ends, the machine model and any measurements you can take safely. Our engineers will tell you which dimensions are still missing.

What if I do not know the steel-core diameter?

Send the coated outside diameter and clear photos. The steel-core diameter can be confirmed during technical review.

What if my end fitting is not a standard type?

Send a drawing or clear photos from several angles with a scale. We stock more than 60 standard fittings and can make custom fittings from drawings.

How long does the technical review take?

We review your information and confirm any missing dimensions or drawing details before we quote.

Send us your measurements

Share your measurements and photos and we will confirm the specification before quoting. Production begins only after you approve it.

Related pages