When sourcing replacement gym cables, most buyers focus on the wire rope itself —the diameter, the coating, the flexibility. But the end-fittings are equally critical. They determine whether the cable physically fits your machine, how safely it connects under load, and how easy it is for gym staff to replace.
At Yongrui, we supply fully assembled cable solutions with 60+ accessory SKUs —from bare wire rope to factory-swaged, pull-tested, ready-to-install assemblies. This guide walks you through every decision you need to make.
1. Common End-Fitting Types
The right terminal depends on how the cable connects to the weight stack, handle, or anchor point on your specific machine. Here are the four primary categories:
Not sure which fitting your machine uses? Send us a photo of the existing cable end and the machine model number. Our engineers will identify the exact fitting type and provide a matched replacement spec —free of charge.
2. Accessory SKU Reference —Key Stock Items
The following are catalogue SKU families. Match the specific suffix and drawing before ordering; stock, prices, MOQ and lead time require quotation confirmation.
| SKU | Type | Catalog distinction |
|---|---|---|
| YR-1602-A/B | Shank ball joints | 11.6 mm head; 3.4/4.2 mm inner hole, respectively |
| YR-1603-A/B | Metal eyelets | Galvanized; select by cable and drawing |
| YR-1604-A/B | Short eyelets | A: galvanized; B: stainless |
| YR-1605 family | Stoppers and lock-sleeve connectors | Suffix identifies the specific assembly |
| YR-1611-A/B/B-2/C/D | Threaded plugs | M12 / M12 long / M12 black / M14 / M16 |
| YR-1612-A/B/C/D/E/F/G | Planar, cylinder and self-tightening joints | Not pulleys; match the individual drawing |
| YR-1680 / YR-1681 | Pulleys | Plastic / aluminum families; suffix defines size or bracket |
3. Why Professional Swaging is Non-Negotiable
In a commercial gym environment, an end-fitting failure is not a maintenance issue —it's a safety incident. A cable under a 200 lb weight stack that pulls free of its fitting can cause serious injury.
What is Hydraulic Swaging?
Swaging is the process of cold-deforming a metal ferrule or fitting around the cable wires using hydraulic force. Press settings depend on the cable, fitting and approved process specification. Assembly strength must be verified for the specific termination rather than assumed from a generic press-tonnage figure.
Swaged and other termination designs must be qualified as complete assemblies. Incorrect tooling, compression or cable matching can cause a swaged connection to fail; no method is automatically slip-proof.
Our Quality Control Process
- Hydraulic swaging press —calibrated to the wire diameter and fitting material for consistent compression
- Agreed test plan —confirm sample destructive tests, proof-load testing and acceptance criteria for the exact cable and fitting; these are different procedures
- Visual inspection —coating continuity check at the fitting junction to prevent moisture ingress
- Documentation —test certificates available for OEM customers and quality audits
Do not substitute unapproved hardware or assemble a load-bearing termination without an approved process. Use the equipment manufacturer’s specified connection and qualified assembly; fitting suitability cannot be inferred from its appearance alone.
4. How to Measure for a Custom Cable Order
To generate an accurate quote and ensure a perfect fit, provide these three measurements:
Total Assembly Length
For the measurement method used in this guide, lay the cable straight without tension and measure from the outermost end of one fitting to the outermost end of the other, including both fittings. Record it in millimetres, for example 1,850 mm overall. If your machine drawing uses bearing-point length instead, send that drawing or mark the two reference points in a photo so we can help check the corresponding overall length. Confirm the final dimensions on the order drawing before production. See our illustrated gym cable measurement guide.
Cable Diameter —Two Numbers Required
Specify both the steel core diameter and the finished OD after coating. These are different. Example: Ø3.18mm core / Ø4.76mm OD (Nylon coated). If you only have the finished OD, our team can back-calculate the core size.
Fitting Specifications
For eyelets: the bolt hole diameter (e.g., 10mm hole for M10 bolt). For ball shanks: the ball diameter and shank length. For threaded studs: the thread size and engagement length. A photo of the existing fitting with a ruler is always helpful.
Send us a clear photo of the old cable next to a ruler, plus your machine brand and model. Our engineering team can identify the specification from photos alone for most major brands (Life Fitness, Technogym, Precor, Matrix). Submit a photo inquiry →
5. Why Order Assembled Cables from Yongrui?
Frequently Asked Questions
Ready to Order Your Custom Assembly?
Stop fitting generic cables to machines they weren't designed for. Send us your spec, a photo, or your machine model for an application-specific quotation after review.
Get a Free Quote → Build Your Cable Spec →